Z axis adjustment

Post Reply
bauchetfranck62@gmail.com
Posts: 4
Joined: Sun Dec 01, 2019 9:54 pm

Z axis adjustment

Post by bauchetfranck62@gmail.com » Sun Dec 01, 2019 11:27 pm

hello,
I have problems with Z axis.

I try to adjust screw with the 2 motors.

the better result i've got is: the to motors turn when i turn slowly, step by step but after 3 cm, the right stop turn ( the motor turns but we have a noise at the coupling nut)

I try to tighten the screw of the coupling more or less, it's the better adjustement that i've got
I try to put oil on the endless screw

please help

thank you

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Z axis adjustment

Post by William » Mon Dec 02, 2019 10:53 am

Hi, If you are referring to the z-axis not moving properly,
You can check the following:
1. Check whether the threaded rod is bent, and replace it if it is bent;
2. Check whether the z-axis brass nut is over-tightened and can be loosened properly;
3. Check whether the left and right sides of the z-axis are on the same horizontal line and adjust it;
4. Is the coupling installed correctly?
Specific operations can refer to this: http://geeetech.com/forum/viewtopic.php?f=82&t=60931
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

bauchetfranck62@gmail.com
Posts: 4
Joined: Sun Dec 01, 2019 9:54 pm

Re: Z axis adjustment

Post by bauchetfranck62@gmail.com » Sun Dec 08, 2019 10:50 pm

Thank you

i've loosen differrents screw and add some grease and it's done

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Z axis adjustment

Post by William » Mon Dec 09, 2019 9:19 am

:D
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Mentos56
Posts: 1
Joined: Wed Nov 06, 2019 12:36 pm

Re: Z axis adjustment

Post by Mentos56 » Tue Dec 10, 2019 3:27 am

Check you pot on the circuit board. You should be putting out 0.61 volts. Put the negative side of multimeter on the negative power supply, then put positive lead on the pod and you will get a reading. All pods should read 0.61 volts with exception of the extruder which is 0.72 volts.
Another check and I have done this before do you have the x and y axis reversed. The printer will print like this and is a mind blowing experience when you find out your plugged in wrong.

picyw
Posts: 1
Joined: Tue Oct 26, 2021 12:39 pm

Re: Z axis adjustment

Post by picyw » Tue Oct 26, 2021 12:40 pm

Gree tech is sharing the post of 3D printer with the establishment of the series with the face of problem in Z axis. I tried to adjust the screw with the 2 motors that is a better do my assignment adjustment with the sign note of please help way of betterments.

annonimuse
Posts: 2
Joined: Thu Oct 28, 2021 1:39 pm

Re: Z axis adjustment

Post by annonimuse » Thu Oct 28, 2021 1:39 pm

You are not only the one who is facing z axis issues. I am also and there are many users who are using x and y axis car lockout service accordingly and most of the time z axis adjustment issues are causing the major problems.

pixizejy
Posts: 1
Joined: Sat Nov 13, 2021 3:27 pm

Re: Z axis adjustment

Post by pixizejy » Sat Nov 13, 2021 3:28 pm

The board of the index has some obituaries with opinions this was good to have the data along with the parts that were good to read on it. I need to make a report on this so I need to know if iv therapy phoenix is reliable or not so I can get data through these forums or make my project complete.

Post Reply