M201 and 3DTouch.

Post Reply
Bs2000
Posts: 16
Joined: Sat May 11, 2019 3:42 am

M201 and 3DTouch.

Post by Bs2000 » Sat May 11, 2019 6:12 am

Did anyone find out if the z-min connections work and get source code for the M201 so we can add 3dtouch

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: M201 and 3DTouch.

Post by _kaktus_ » Sat May 11, 2019 5:38 pm

Hi.
:mrgreen:

When I was a new M201 user, I thought just like you. I wanted to have an automatic levelling device. :D

Today I think it's a superfluous gadget. :lol: Of course, if someone wants to have it, I won't advise against it. ;)

It is possible that when our printer will have a redesigned Firmware, it will be possible to add such a peripheral. Unfortunately, this is not the case today.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Bs2000
Posts: 16
Joined: Sat May 11, 2019 3:42 am

Re: M201 and 3DTouch.

Post by Bs2000 » Sun May 12, 2019 11:10 pm

How do you know they are going to redesign the firmware? They told me a few days ago that they have suspended updates to the M201 because of new models.

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: M201 and 3DTouch.

Post by _kaktus_ » Mon May 13, 2019 12:46 am

Hi.
:mrgreen:

You can't take it literally. :roll:
A new version of the branded firmware is simply created, that can be adapted to our model. :D
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Bs2000
Posts: 16
Joined: Sat May 11, 2019 3:42 am

Re: M201 and 3DTouch.

Post by Bs2000 » Mon May 13, 2019 8:48 am

Well I sure hope so seeing I had just purchased this machine and for the amount of money I paid I would have went with a newer model if I know all this beforehand

User avatar
_kaktus_
Site Admin
Posts: 1260
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: M201 and 3DTouch.

Post by _kaktus_ » Mon May 13, 2019 12:34 pm

HI.
:mrgreen:

Oh, yeah, right.

Don't worry.
This is a very good DIY model. :D
I would have chosen it again.

But the fact is that the price has risen recently.
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

Bs2000
Posts: 16
Joined: Sat May 11, 2019 3:42 am

Re: M201 and 3DTouch.

Post by Bs2000 » Wed Dec 22, 2021 8:29 pm

Has this yet to be figured out? here we are 4 yrs later and still so limited with the m201

Post Reply