GiantArm D200 3D printer
Posted: Thu May 24, 2018 12:26 am
Very, very disappointed!
Obviously no one has to complain about the D200. Well, I'll start!
I bought this promising machine 3 weeks ago now, and spent 9/10 of my time trying to make it work properly.
Problem # 1: The new version software does not work, I had to keep the previous version.
Problem # 2; the firmware update blocked my machine, I had to put back the old version.
Problem # 3: The printer is unable to print ABS without adding a maintenance product, Dimafix style or other. I searched for 4 days before realizing it.
Problem n ° 4: the nozzles clog up without stopping, the printing starts normally then after one hour the filament does not pass anymore ????
In short, it's been 3 weeks now that I try to print and I could only release 4 pieces correctly, the rest left in the trash. I admit that I am disgusted and I do not know what to do, except to warn you not to buy this machine!
Très, très déçu !
Visiblement personne n'a à se plaindre de la D200. Et bien , je vais commencer !
J'ai acheté cette machine prometteuse il y a maintenant 3 semaines, et j'ai passé les 9/10 de mon temps à essayer de la faire fonctionner correctement.
Problème n°1 : le logiciel nouvelle version ne fonctionne pas, j'ai du garder la version antérieure.
Problème n°2 ; la mise à jour du firmware a bloqué ma machine, j'ai dû remettre l'ancienne version.
Problème n°3 : L'imprimante est incapable d'imprimer de l'ABS sans ajouter un produit de maintien, du style Dimafix ou autre. J'ai cherché pendant 4 jours avant de m'en rendre compte.
Problème n°4 : les buses se bouchent sans arrêt, l'impression commence normalement puis au bout d'une heure le filament ne passe plus ????
Bref, cela fait maintenant 3 semaines que j'essaye d'imprimer et je n'ai pu sortir que 4 pièces correctement, le reste est parti à la poubelle. J'avoue que je suis dégouté et je ne sais plus quoi faire, si ce n'est de vous avertir de ne pas acheter cette machine !
Obviously no one has to complain about the D200. Well, I'll start!
I bought this promising machine 3 weeks ago now, and spent 9/10 of my time trying to make it work properly.
Problem # 1: The new version software does not work, I had to keep the previous version.
Problem # 2; the firmware update blocked my machine, I had to put back the old version.
Problem # 3: The printer is unable to print ABS without adding a maintenance product, Dimafix style or other. I searched for 4 days before realizing it.
Problem n ° 4: the nozzles clog up without stopping, the printing starts normally then after one hour the filament does not pass anymore ????
In short, it's been 3 weeks now that I try to print and I could only release 4 pieces correctly, the rest left in the trash. I admit that I am disgusted and I do not know what to do, except to warn you not to buy this machine!
Très, très déçu !
Visiblement personne n'a à se plaindre de la D200. Et bien , je vais commencer !
J'ai acheté cette machine prometteuse il y a maintenant 3 semaines, et j'ai passé les 9/10 de mon temps à essayer de la faire fonctionner correctement.
Problème n°1 : le logiciel nouvelle version ne fonctionne pas, j'ai du garder la version antérieure.
Problème n°2 ; la mise à jour du firmware a bloqué ma machine, j'ai dû remettre l'ancienne version.
Problème n°3 : L'imprimante est incapable d'imprimer de l'ABS sans ajouter un produit de maintien, du style Dimafix ou autre. J'ai cherché pendant 4 jours avant de m'en rendre compte.
Problème n°4 : les buses se bouchent sans arrêt, l'impression commence normalement puis au bout d'une heure le filament ne passe plus ????
Bref, cela fait maintenant 3 semaines que j'essaye d'imprimer et je n'ai pu sortir que 4 pièces correctement, le reste est parti à la poubelle. J'avoue que je suis dégouté et je ne sais plus quoi faire, si ce n'est de vous avertir de ne pas acheter cette machine !