Search found 6340 matches

by William
Tue Sep 08, 2020 9:31 am
Forum: Extruder
Topic: A30M Extruding different lengths between sides for same feed length
Replies: 1
Views: 10237

Re: A30M Extruding different lengths between sides for same feed length

Hello, the tightness of your extruder gear may be the cause of this phenomenon, you can calibrate the extruder, you can refer to the link below for calibration. :D
https://www.youtube.com/watch?v=xzQjtWhg9VE
by William
Mon Sep 07, 2020 4:42 pm
Forum: Geeetech A30 Series
Topic: Install 3D touch instead of capacitive proximity senso
Replies: 1
Views: 4802

Re: Install 3D touch instead of capacitive proximity senso

Hello, you can check if there is an adapter board interface on your hot end, just connect 3d to the adapter board. :D
by William
Mon Sep 07, 2020 3:33 pm
Forum: Geeetech A20
Topic: Températures bed et extrudeur reviennent toujours à des valeurs non souhaitées.
Replies: 1
Views: 7929

Re: Températures bed et extrudeur reviennent toujours à des valeurs non souhaitées.

Bonjour, vous pouvez supprimer directement le startgcode, puis régler la température. :D
by William
Mon Sep 07, 2020 11:56 am
Forum: Geeetech A10 Series
Topic: GeeeTech A10M not printing.
Replies: 1
Views: 2626

Re: GeeeTech A10M not printing.

Hello, according to your description, if your nozzle is not extruding, it may be blocked at the hot end. You can refer to the video below to clean it up. There is another possibility. Please observe whether the temperature of the nozzle reaches 210°C. If possible, you can also take a picture to solv...
by William
Mon Sep 07, 2020 11:31 am
Forum: Geeetech I3 Pro B
Topic: Z Axis Trouble after 3D Touch Install
Replies: 13
Views: 19739

Re: Z Axis Trouble after 3D Touch Install

Hello, if your 3dtouch is too far away from the hot bed, you can refer to the link below to adjust the z offset distance. :D
viewtopic.php?f=27&t=18371
by William
Mon Sep 07, 2020 10:34 am
Forum: Control Board
Topic: * SOLVED * Huge problem with GT2560 board
Replies: 75
Views: 141273

Re: * SOLVED * Huge problem with GT2560 board

Hello, you can re-upload the new firmware to overwrite it. :D
by William
Fri Sep 04, 2020 2:46 pm
Forum: Geeetech A20
Topic: Problems with upper layers
Replies: 3
Views: 9409

Re: Problems with upper layers

Hello, since you have replaced the nozzle, the extruder has been calibrated, the filament has been replaced, and the hot end has been cleaned. This still happens. So I want you to make a few suggestions: 1. Your consumables may be oxidized, resulting in poor extrusion. You can change to another cons...
by William
Fri Sep 04, 2020 11:19 am
Forum: Geeetech A30 Series
Topic: Change temperature sensor pin Gtm32pro vd board?
Replies: 1
Views: 4587

Re: Change temperature sensor pin Gtm32pro vd board?

Hello, if there is no problem with your thermistor, it should be a circuit problem. You can check whether the circuit is broken.
You cannot solve it by changing the pins and updating the firmware, because the firmware of a30 cannot be changed. :D
by William
Fri Sep 04, 2020 9:32 am
Forum: Geeetech I3 Pro B
Topic: Extruder board port not working
Replies: 2
Views: 4677

Re: Extruder board port not working

Hello, if you find that the problem is not the driver by replacing the driver, it may be a cable problem. You try to change the cable of another axis to see if it is the problem. It may also be a problem with the structure of the extruder. You can refer to this link. :D http://www.geeetech.com/forum...
by William
Thu Sep 03, 2020 11:09 am
Forum: Geeetech A10 Series
Topic: Micro Swiss hotend
Replies: 6
Views: 6816

Re: Micro Swiss hotend

Hello, as long as it can be successfully engaged, it can be used normally. And then adjust the nozzle diameter on the slicing software. :D