Search found 25 matches
- Sun Oct 17, 2021 6:47 am
- Forum: A20T
- Topic: Can’t get A20T extruder unplugged... any suggestions welcome
- Replies: 2
- Views: 2655
Can’t get A20T extruder unplugged... any suggestions welcome
Fellow printers, I’m trying to get my A20T working again— my wife asked me to do a project for her which requires the A20T. Two of the three filament paths are clear (I can manually push cleaning filament into the top Bowden tube and it comes out the nozzle). However the third path is really plugged...
- Sat Oct 16, 2021 7:04 am
- Forum: A20T
- Topic: After a print, retract filament? Pull back bowden tube?
- Replies: 1
- Views: 2243
After a print, retract filament? Pull back bowden tube?
Fellow printers, I'm trying to get back to printing with an A20T. I had frequent extruder jams in the past. After you finish a print, do you just let the printer cool down or do you retract some filament, or pull back the bowden tubes? Any suggestions for avoiding jams? Any preventative maintenance?
- Sat Oct 16, 2021 6:59 am
- Forum: A20T
- Topic: Any tips for stopping the extruder/nozzle from jamming?
- Replies: 3
- Views: 3815
Re: Any tips for stopping the extruder/nozzle from jamming?
THANK YOU! I had given up on the A20T, but I'd like to try getting it working again. I'll try your suggestions.
- Sat Oct 16, 2021 6:54 am
- Forum: A20T
- Topic: Anyone have an A20T profile for PrusaSlicer?
- Replies: 3
- Views: 3558
Re: Anyone have an A20T profile for PrusaSlicer?
No. I gave up (temporarily, hopefully) on the A20T because the nozzle keeps jamming...
I never did get a working prusaslicer profile set up.
I never did get a working prusaslicer profile set up.
- Sat Aug 28, 2021 11:09 pm
- Forum: A20T
- Topic: Anyone else trying to use Diamond nozzle?
- Replies: 0
- Views: 1713
Anyone else trying to use Diamond nozzle?
Fellow printers,
I’m using a Diamond 3in 1 out nozzle but having lots of problems with jamming. The nozzle came from Greentree...
Anyone had luck with the Diamond nozzle?
I’m using a Diamond 3in 1 out nozzle but having lots of problems with jamming. The nozzle came from Greentree...
Anyone had luck with the Diamond nozzle?
- Sat Aug 28, 2021 10:50 pm
- Forum: Geeetech I3 Pro C
- Topic: What volumetric flow, or mm/s filament rate do you use?
- Replies: 2
- Views: 5248
Re: What volumetric flow, or mm/s filament rate do you use?
I found in Geeetech’s scattered documentation that the flow rate of the extruder is about 24cc/h which works out to 6.6mm^3/s, which is about what I’m finding. I’m still curious what flow rate others are using to minimize the extruder servo “clicking”...
- Sat Aug 28, 2021 10:48 pm
- Forum: Geeetech I3 Pro C
- Topic: How to adjust heights of dual extruder nozzles?
- Replies: 1
- Views: 5182
Re: How to adjust heights of dual extruder nozzles?
Never mind... figured it out.
- Sat Aug 28, 2021 10:46 pm
- Forum: Geeetech I3 Pro C
- Topic: Which bed leveling mode in Marlin with 3d-touch? Bilinear?
- Replies: 0
- Views: 4072
Which bed leveling mode in Marlin with 3d-touch? Bilinear?
Fellow Printers, I have a I3 pro C with 3D Touch. The auto leveling only picks a single point in the center. I would like to use the most accurate auto mesh leveling available in Marlin 2.x for this printer and 3D Touch. Do I recompile Marlin with “ //#define AUTO_BED_LEVELING_BILINEAR” uncommented?...
- Sat Aug 28, 2021 4:54 am
- Forum: Geeetech I3 Pro C
- Topic: What volumetric flow, or mm/s filament rate do you use?
- Replies: 2
- Views: 5248
What volumetric flow, or mm/s filament rate do you use?
Fellow printers, I’m having problems with the extruder steppers “clicking” during a print. The filament is set up so there is practically no friction coming off the spool. I’m using PLA at 215 degrees. Both extruders seem to click about the same amount. I’m worried that the extruder can’t heat the f...
- Wed Aug 11, 2021 12:25 am
- Forum: A20T
- Topic: Any tips for stopping the extruder/nozzle from jamming?
- Replies: 3
- Views: 3815
Any tips for stopping the extruder/nozzle from jamming?
Fellow printers,
Seems most times I try to print another test on the A20T, at least one of the three extruder paths is plugged. Any ways to avoid this?
Seems most times I try to print another test on the A20T, at least one of the three extruder paths is plugged. Any ways to avoid this?